Placa USB4Butiá
Bill of Materials USB4Butiá
| Component
|
Quantity
|
Description
|
PCB Identifier
|
| PIC 18F4550 |
1 |
microcontroller |
PIC18F4550
|
| Socket 40pin |
1 |
socket for the microcontroller |
|
| RJ45 Female Jack |
6 |
5555167-1 type |
RJ45
|
| USB Female Type B |
1 |
USB_B
|
| ax12 female bus connector |
1 |
molex WM18901-ND connector type |
AX-12
|
| 120R |
1 |
resistor |
120Ω
|
| 390R |
2 |
resistor |
390Ω
|
| 1K |
2 |
resistor |
1KΩ
|
| 10K |
8 |
resistor |
10KΩ
|
| 1M |
1 |
resistor |
1MΩ
|
| 22PF |
2 |
capacitor |
22pF
|
| 0.1UF |
4 |
capacitor |
0.1uF
|
| 0.47UF |
1 |
capacitor |
0.47uF
|
| electrolitic capacitor 10UF, 25V, 20% |
1 |
lower than 7mm |
10uF
|
| Led 3mm |
1 |
|
LED
|
| 20MHZ crystal |
1 |
height 0.138" (3.50mm) |
Crystal 20MHZ
|
| 4.3mm switch |
2 |
|
RST SW1, PROG SW2
|
| Female Header |
11 |
|
h1..h11
|
Shield para motores
Bill of materials for USB4Butiá motor shield
| Component
|
Quantity
|
Description
|
PCB Identifier
|
| L298HN |
1 |
HBridge |
U1 L298
|
| 1A7 |
8 |
diode |
D1..D8
|
| male headers |
14 |
pin |
P1..P4
|
| 100nF (10V minimum, 20% tolerance) |
2 |
ceramic capacitor |
C1, C2
|
Placa Sensores
Bill of Materials allselasercut
| Component
|
Quantity
|
Description
|
PCB Identifier
|
| Rj45 female jack |
5 |
5555167-1 type |
RJ45
|
| 470uf electronic capacitor |
1 |
25V |
C1 CAPAPOL
|
| Resistor 10kΩ |
4 |
5% tolerance, 1/4w power |
|
| Resistor 6.8kΩ |
1 |
5% tolerance, 1/4w power |
|
| Resistor 120Ω |
2 |
5% tolerance, 1/4w power |
|
| Resistor 1kΩ |
2 |
5% tolerance, 1/4w power |
|
| Resistor 68kΩ |
2 |
5% tolerance, 1/4w power |
|
| Led |
2 |
high intensity green led like 365-1174-ND |
|
| Photoresistor |
3 |
10K-200K OHM 4.20MM LXD4548 |
|
| GP2Y0A21YK0F |
1 |
Sharp Sensor 10-80cm |
|
| Pushbutton |
1 |
KS-03Q-02 |
|
| Pushbutton cap |
1 |
ACC-C17-6 |
|
each module specified in plantilla_allsenV2_lasercut-F_SilkS must be cuted with mouse bite technique or similar
