Diferencia entre revisiones de «Especificaciones fabricación»
De Proyecto Butiá
(→Shield para motores) |
(→Placa USB4Butiá) |
||
| Línea 35: | Línea 35: | ||
|0.47UF||1||capacitor||0.47uF | |0.47UF||1||capacitor||0.47uF | ||
|- | |- | ||
| − | |electrolitic capacitor 10UF, 25V, 20%||1|| lower than 7mm||10uF | + | |[http://www.digikey.com/product-detail/en/ECA-1EM471B/P10379TB-ND/268464 electrolitic capacitor 10UF, 25V, 20%]||1|| lower than 7mm||10uF |
|- | |- | ||
|Led 3mm||1|| ||LED | |Led 3mm||1|| ||LED | ||
Revisión del 17:49 27 ene 2014
Placa USB4Butiá
| Component | Quantity | Description | PCB Identifier | |
|---|---|---|---|---|
| PIC 18F4550 | 1 | microcontroller | PIC18F4550 | |
| Socket 40pin | 1 | socket for the microcontroller | under PIC18F4550 | |
| RJ45 Female Jack | 6 | CONN MOD JACK R/A 8P8C | RJ45 | |
| USB Female Type B | 1 | CONN USB RECEPT R/A TYPE B 4POS | USB_B | |
| ax12 bus connector | 1 | CONN HEADER 3POS 2.5MM R/A TIN | AX-12 | |
| 120R | 1 | resistor 5% tolerance, 1/4w power | 120Ω | |
| 390R | 2 | resistor 5% tolerance, 1/4w power | 390Ω | |
| 1K | 2 | resistor 5% tolerance, 1/4w power | 1KΩ | |
| 10K | 8 | resistor 5% tolerance, 1/4w power | 10KΩ | |
| 1M | 1 | resistor 5% tolerance, 1/4w power | 1MΩ | |
| 22PF | 2 | capacitor | 22pF | |
| 0.1UF | 4 | capacitor | 0.1uF | |
| 0.47UF | 1 | capacitor | 0.47uF | |
| electrolitic capacitor 10UF, 25V, 20% | 1 | lower than 7mm | 10uF | |
| Led 3mm | 1 | LED | ||
| 20MHZ crystal | 1 | height 0.138" (3.50mm) | Crystal 20MHZ | |
| switch | 2 | 4.3mm microswitch | RST SW1, PROG SW2 | |
| Female Header | 11 | Contact spacing 2.54mm (0.1") | h1..h11 |
PCB material specification:
- FR4 Material
- 1.6MM Thickness
- HASL Lead Free Surface Finish
- 1oz Copper Thickness
- Green Solder Mask
- White Silkscreen
- USB4Butiá Gerber file
Shield para motores
| Component | Quantity | Description | PCB Identifier |
|---|---|---|---|
| L298HN | 1 | HBridge | U1 L298 |
| 1A7 | 8 | diode | D1..D8 |
| male headers pins | 14 | Contact spacing 2.54mm (0.1") | P1..P4 |
| 100nF (10V minimum, 20% tolerance) | 2 | ceramic capacitor | C1, C2 |
PCB material specification:
- FR4 Material
- 1.6MM Thickness
- HASL Lead Free Surface Finish
- 1oz Copper Thickness
- Green Solder Mask
- White Silkscreen
- USB4Butiá motor shield Gerber file
Placa Sensores
| Component | Quantity | Description | PCB Identifier |
|---|---|---|---|
| Rj45 female jack | 5 | 5555167-1 type | RJ45 |
| 470uf electronic capacitor | 1 | 25V | C1 CAPAPOL |
| Resistor 10kΩ | 4 | 5% tolerance, 1/4w power | |
| Resistor 6.8kΩ | 1 | 5% tolerance, 1/4w power | |
| Resistor 120Ω | 2 | 5% tolerance, 1/4w power | |
| Resistor 1kΩ | 2 | 5% tolerance, 1/4w power | |
| Resistor 68kΩ | 2 | 5% tolerance, 1/4w power | |
| Led | 2 | high intensity green led like 365-1174-ND | LED |
| Photoresistor | 3 | 10K-200K OHM 4.20MM LXD4548 | LDR |
| GP2Y0A21YK0F | 1 | Sharp Sensor 10-80cm | sharp |
| Pushbutton | 1 | KS-03Q-02 | SW_PUSH |
| Pushbutton cap | 1 | ACC-C17-6 |
PCB material specification:
- FR4 Material
- 1.6MM Thickness
- HASL Lead Free Surface Finish
- 1oz Copper Thickness
- Green Solder Mask
- White Silkscreen
- Each module specified in plantilla_allsenV2_lasercut-F_SilkS must be cuted with mouse bite technique or similar
- The sharp sensor must be connected in this way
